How To Change Husqvarna Edger Blade 323e

• Contents
• Table of Contents
• Bookmarks

  Also Run across for Husqvarna 323E

  Related Manuals for Husqvarna 323E

  Summary of Contents for Husqvarna 323E

• Folio one Operator´s manual 323E 325E 10-series Delight read these instructions carefully and make certain English you empathise them before using the motorcar.

• Page 2: Explanation Of Symbols

  Explanation OF SYMBOLS Symbols • Arrows which testify limits for han- dle mounting. Alarm! The edger can be dangerous! Devil-may-care or incorrect apply tin result in serious or fatal injury to the • Always habiliment approved protective operator or others. gloves.

• Page 3: Table Of Contents

  CONTENTS List of Contents Husqvarna AB has a policy of continuous production development and therefore reserves the right to modify the design and ap- pearance of products without prior detect. EXPLANATION OF SYMBOLS Symbols ................2 CONTENTS List of Contents ..............iii...

• Page 4: Rubber Instructions

  SAFETY INSTRUCTIONS Personal protective equipment The machineʼs safety equipment This section describes the machineʼs safety equipment, its func- Important INFORMATION tion and how checks and maintenance are carried out to ensure that it operates correctly. (See the affiliate "What is what" to •...

• Page 5: Cut Equipment

  SAFETY INSTRUCTIONS 4. Vibration damping 5. Muffl er organisation The muffl er is designed to give the lowest possible noise Your machine is equipped with level and to directly the engineʼs a vibration damping system, exhaust fumes away from the which is designed to requite as operator.

• Page half-dozen: Command, Maintenance And Service Of The

  Prophylactic INSTRUCTIONS Control, maintenance and service of three. Cutting attachment guard the machineʼs condom equipment • Ensure that the guard is united nations- damaged and is not cracked. Of import INFORMATION • All service and repairs to the machine require special • Supercede the guard if it has training.
• Page vii Safe INSTRUCTIONS 6. Cut equipment 7. Locking nut • Protect your hand from injury The two basic rules: when assembling, utilise the blade guard as protection Merely use the cut equip- when tightening with a socket ment we recommend! See spanner.

• Page 8: General Prophylactic Instructions

  SAFETY INSTRUCTIONS General safe instructions Safety instructions before starting work • Inspect the working area. Remove any objects, such as stones, cleaved glass, nails, steel wire, string, etc. that can be IMPORTANT INFORMATION thrown or can wrap around the blade or blade guard. •...

• Page 9: Fuel Safety

  Safety INSTRUCTIONS Kickoff Fuel safety Alert! • Always employ a fuel container When the engine starts with the choke lever with an anti-spill valve. in the choke or starter throttle position the cut tool (blade or trimmer) starts to rotate •...

• Page 10: Full general Working Instructions

  Condom INSTRUCTIONS General working instructions Basic working techniques Safety instructions while working Of import Information • This section takes upward the bones safety precautions for • Always ensure you have a working with the edger. safe and fi rm foothold. • If you encounter a situation where you are uncertain how to go along yous should ask an skilful.
• Page eleven SAFETY INSTRUCTIONS Safety instructions subsequently completing work • Ensure the bract has stopped before cleaning, auto- rying out repairs or an inspec- tion. Remove the spark plug cable from the spark plug. • Wear heavy-duty gloves when conveying out repairs on the edger.

• Page 12: What Is What

  WHAT IS WHAT? What is what on the edger? Blade fourteen. Air purge Grease fi ller cap 15. Air fi lter cover Angle gear 16. Clutch comprehend Blade baby-sit 17. Handlebar adjustment Shaft 18. Locking nut Loop handlebar nineteen. Support fl ange Throttle 20.

• Folio xiii: Assembly

  Assembly Assembling the loop handlebar Assembling the blade • Position the handle on the Fit the blade as follows: shaft. Note that the handle must be mounted beneath the Fit the drive disc (A) on arrow on the shaft. the outgoing shaft. Make certain that the border that fi...

• Folio 14: Fuel Treatment

  ii-stroke disrupt operations. engines. Mixing ratio 1:50 (2%). • Ensure that the fuel is • If HUSQVARNA ii stroke well mixed by shaking the oil is not available you can container earlier fi lling the use a loftier quality 2-stroke tank.

• Page 15: Start And End

  START AND Terminate Control earlier starting For reasons of safety follow Asphyxiate: Set the choke control these recommendations! in the asphyxiate position. • Bank check that the support fl ange is not cracked due to fatigue or due to being tightened too much.

• Folio 16: Maintenance

  MAINTENANCE Carburettor Bones setting Your Husqvarna product has been designed and manufactured to specifi cations that reduce harmful emissions. • The carburettor is set to its basic setting when test run at the Afterwards your unit has been run viii-ten tanks of fuel the engine has factory.
• Folio 17 MAINTENANCE Last setting of the idling speed T Correctly adjusted carburettor A correctly adapted carburettor means that the car accelerates without hesitation and the automobile iv-cycles a footling Adjust the idling speed with at max speed. Furthermore, the cutting attachment must non the screw T, if it is necessary rotate/motility at idling.

• Page xviii: Muffl Er And Catalytic Converter

  MAINTENANCE Muffl er with catalytic converter Cooling arrangement To maintain equally low an A muffl er fi tted with a catalytic converter reduces the extent of operating temperature every bit the following substances in the exhaust fumes: possible the engine is equipped with a cooling •...

• Page nineteen: Air Fi Lter

  "Oiling the air fi lter". Oiling the air fi lter Adjusting the edger's cut depth Always utilise HUSQVARNA fi lter oil, order no. 503 47 73-01. The fi lter oil contains The cut depth should exist a solvent to make it spread adjusted before starting piece of work.

• Page 20: Maintenance Schedule

  MAINTENANCE Maintenance schedule Weekly maintenance Bank check the starter, the Below follows some general maintenance instructions. If you starter string and the render need further information delight contact your service workshop. spring. Daily maintenance Make sure that the vibration damping Clean the outside of the elements are not machine.
• Page 21 MAINTENANCE Monthly maintenance Make clean the fuel tank using petrol. Clean the exterior of the carburettor and the area surrounding it. Clean the fan wheel and the area around it. Check the fuel fi lter and the fuel pipe, replace if necessary.

• Page 22: Technical Data

  TECHNICAL DATA Technical information 323E 325E X-series Engine Displacement, cu. in/cm 1,50/24,5 one,50/24,v Cylinder diameter, inch/mm 1,34/34 1,34/34 Stroke length, inch/mm ane,06/27 1,06/27 Recommended max. speed, rpm 11 000-11 700 xi 000-11 700 Idling speed, rpm two 700 2 700...
• Page 23 EC-declaration of conformity (Applies to Europe but) We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel. +46 36-146500, declare under sole responsibility that the edger Husqvarna 323E and 325E from the serial numbers of 2002 and onwards (the year is conspicuously stated in obviously text on...
• Page 24 114 02 68-26 ´®z+H:r¶62¨ ´®z+H:r¶62¨ 2004W13...

Source: https://www.manualslib.com/manual/576819/Husqvarna-323e.html

Posted by: jacksondebefors.blogspot.com

Share this post